Quickstart - Jellox Analog EN

Owned by Marcel Ortler
Last updated: Sept 11, 2024 by Stefanie Buber
5 min read

For the English version click the following link: Quickstart - Jellox Analogue EN

1. Delivery condition and prerequisits

Thank you for choosing Jellox.

a. You can check the order against the delivery slip to ensure it is complete.

  • Quick start guide

  • Delivery slip with listing by commission and composition of the measurement system

  • Packaging material with information on the commission and composition of the measurement system

  • Devices (according to commission and measurement system)

    • 1x Jellox data logger

    • 1x antenna as per order

    • 1x 7-pin connection cable (optional)

    • 1x magnet

    • up to 4 remote sensors as per order

      • Radar sensor

      • Gauge sensor

  • Jellox user manual

b. Unpack the radar sensor and position it so that the radar antenna points towards the ceiling.

Unbenanntes Diagramm-1719304578808.drawio (2)-20240626-064433.png

 

1 Radar antenna

 

2. Connecting Jellox

anschluss.drawio (1)-20240624-120745.png
Connectors of the Jellox

1 Antenna connector

2 Analogue sensor connector

Haben Sie noch Fragen zu diesem Schritt? Eine Sammlung von Antworten finden Sie hier.

3. Commissioning Jellox

Tap the supplied magnet for at least 3 seconds on the indicated position to set the Jellox to operating mode “normal”. When establishing the connection, the aircraft symbol is replaced by a rotating arrow symbol.

Once the connection is complete, the symbol with rotating arrows disappears again. If the display switches off in the meantime, it can be reactivated with the magnet. To do so, briefly tap the magnet on the position indicated in the video.

 

1 Information about the network connection

Field strength of the mobile network signal during the last connection

 

 

Transport mode activated

2 Status of the mobile network connection

mobile connection disconnected; wait for next connection establishment

 

(blinking)

connecting

 

 

connection to the myDatanet server established

 

 

last connection failed

Do you still have questions about this step? You can find a pool of answers here.

4. Creating a site

a. Log on to the Server.

You will receive the login details and the credit for the server from your responsible sales partner.

 

 

b. Open the wizard.

  1. Create a new site

The serial number can be found on the type plate at the rear of the Jellox and on the packaging.

 

 

 

c. Create the site.

1 Activate the checkbox to switch directly to the input mask for configuring the site.

2 Create site

Do you still have questions about this step? You can find a pool of answers here.

5. Activate and configure analogue input

a. Select the Select the appropriate mode for your analogue sensor

1 Selection of mode

 

 

 

b. Configure the limits

1 Lower limit analogue sensor

2 Upper limit analogue sensor

3 Unit of the analogue sensor

c. Switch to the tab “Configuration“ (3) and set warmup time and voltage.

 

1 Select warmup time

2 Select voltage

3 “Configuration” tab

d. Save your settings

1 Save your settings

 

 

 

e. Trigger a connection to transmit the settings to the device.

 

Do you still have questions about this step? You can find a pool of answers here.

6. View first measurement data

1 View measurement data

 

1 Measurement data analogue sensor

2 Measurement data first remote sensor

 

Do you still have questions about this step? You can find a pool of answers here.

 

 

 

 

Make further adjustments

https://microtronics.atlassian.net/wiki/spaces/Academy/pages/4121854056

FAQs

Please actuate the reed switch for at least 3 seconds until a complete connection is triggered. (Symbol with rotating arrows appears)

Jellox requires a server version of 52v007 or higher. Please contact Microtronics Support, if your myDatanet-Server does not fulfil this requirement.

Jellox Error Codes

A connection with the Jellox is triggered by tapping the magnet on the designated spot for at least 3 seconds.